Read On How To Install Wall Molding
Wall molding are designed to run across either a floor or ceiling. In spite of where the wall molding is headed, the biggest task is to ensure the corners are fitted accordingly. Wall moldings are usually mitered on the corners. What this means is that, a miter saw alongside swivel blades are utilized in cutting the two portions at precisely 450 angles. This ensures that the wall moldings create a corner at the point where they join. Make certain that the miter blade used is sharp. This is because a clean cut is required in order to create a tight miter.
What Youll Need
The following are some of the tools and materials that you will require in order to accomplish the task:
-Tape measure.
-Miter saw.
-Pencil.
-Finish nail gun.
For safety purposes, you will have to put on your safety glasses while creating miter cuts.
Instructions
#1: Measurements
Begin by taking the precise measurements commencing from one end to the extreme end by making use of a tape measure. Choose a section of wall molding which is lengthier compared to the measurements taken. Place the piece on the miter saw. Ensure that its rear is lying on the saw fence. This way, it will be in the exact position when fixed on the wall.
#2: Construction
Place a piece of the molding which is extended compared to wall where it will be placed against the wall. The piece should rest along the rear guide of the miter saw in the same manner that it will rest against the wall. Place the commencing point of the molding beneath the miter blade.
The miter blade should be swiveled to forty five degrees. The blade ought to point inwards towards the extended edge of the molding. Chop it at that point.
Place the molding face down and take the measurement on the rear of the trim. The measurement should be done form the chopped rim which will come into contact with the corner outwards across the stretch of the edge. Indicate the second trim at the space of the extreme corner.
In the same manner that you mitered the first trim, miter the extreme end of the second molding. Just as you did with the first molding, turn the miter blade to forty five degrees inwards.
Repeat the same procedure for every section of wall molding. The moment you have cut all the trims, put each of them in place alongside the mitered spots. The mitered spots ought to butt against one another. Use a finish nail gun to hold the pieces together. When using the finish nail gun, leave a space of roughly one foot on both the upper and base edges.
Wall moldings can greatly enhance the artistic appeal of your house. Hence, if you are thinking of an inexpensive way to refurbish your lounge or dining room, consider using wall moldings. The good thing about wall moldings is that you do not need to be skilled in carpentry in order to accomplish the work.
What Youll Need
The following are some of the tools and materials that you will require in order to accomplish the task:
-Tape measure.
-Miter saw.
-Pencil.
-Finish nail gun.
For safety purposes, you will have to put on your safety glasses while creating miter cuts.
Instructions
#1: Measurements
Begin by taking the precise measurements commencing from one end to the extreme end by making use of a tape measure. Choose a section of wall molding which is lengthier compared to the measurements taken. Place the piece on the miter saw. Ensure that its rear is lying on the saw fence. This way, it will be in the exact position when fixed on the wall.
#2: Construction
Place a piece of the molding which is extended compared to wall where it will be placed against the wall. The piece should rest along the rear guide of the miter saw in the same manner that it will rest against the wall. Place the commencing point of the molding beneath the miter blade.
The miter blade should be swiveled to forty five degrees. The blade ought to point inwards towards the extended edge of the molding. Chop it at that point.
Place the molding face down and take the measurement on the rear of the trim. The measurement should be done form the chopped rim which will come into contact with the corner outwards across the stretch of the edge. Indicate the second trim at the space of the extreme corner.
In the same manner that you mitered the first trim, miter the extreme end of the second molding. Just as you did with the first molding, turn the miter blade to forty five degrees inwards.
Repeat the same procedure for every section of wall molding. The moment you have cut all the trims, put each of them in place alongside the mitered spots. The mitered spots ought to butt against one another. Use a finish nail gun to hold the pieces together. When using the finish nail gun, leave a space of roughly one foot on both the upper and base edges.
Wall moldings can greatly enhance the artistic appeal of your house. Hence, if you are thinking of an inexpensive way to refurbish your lounge or dining room, consider using wall moldings. The good thing about wall moldings is that you do not need to be skilled in carpentry in order to accomplish the work.