How to Install a Bathroom Floor Cabinet
One of the key factors and one of the most important components of a bathroom renovation is the proper use of the space and of course this calls for bathroom floor cabinets.
These cabinets would help clear up the room through the elimination of clutter.
Many modern bathroom floor cabinets make use of either oak or maple components.
However, many manufacturers have expanded their lines to include the use of cherry, hickory as well as pine.
Elaborate bathroom designs might include more than one bathroom floor cabinets in varying finishes to add more effect.
Redoing your bathroom need not be an expensive undertaking.
The most basic and not to mention most economical way of sprucing up an old bathroom is through installing factory manufactured components, This include bathroom sinks as well as bathroom floor cabinets.
Installing a bathroom floor is a fairly easy thing to do.
Any homeowner can do it themselves as a DIY(Do-It-Yourself) project by following some very easy steps.
First thing you must do is to shut off the water service to the sink fixture and disconnect plumbing as well.
If it doesn't have shut-off valves, the main supply to the entire house should be shut off.
If the installation cannot be finished quickly, the bathroom supply lines might need to be capped so that the water service can be turned back on.
Many homeowners also use the time that the water supply is hut down to install new bathroom floor covering, besides the bathroom floor cabinet.
Installation can be done very quickly and is usually done within several hours.
Accurate measurements of the space for the new bathroom floor cabinet is a vital step in making sure that you are getting a cabinet that would properly fit the available space.
Take measurements of the location for both the hot and cold plumbing lines, and then create markings for each one, centered on the back area of the vanity sink cabinet.
After that cut openings for each one making sure that you leave some space to connect all the fittings later.
Set the bathroom floor cabinet in place, making use of the wall markings, be sure to check that they are solidly in place and are leveled.
If they are not leveled, you can make use of wood shims.
Secure it in place through the use of 3-inch screws through the nailer and going into the wall stud.
Then re-check its level again.
If doing it yourself seems more work than you would want to do yourself, you can always hire someone to install the bathroom floor cabinet for you.
There are many skilled people who can do it.
But still, it would not hurt to try it yourself as many of the factory manufactured bathroom floor cabinets actually come with a step by step process that you can follow while you install it.
You can also research about which ways are the easiest as there are, of course, various ways of installing it and each one differs in difficulty.
You can also ask help from someone who knows a little bit about carpentry although these skills are not required to be able to do it yourself.
These cabinets would help clear up the room through the elimination of clutter.
Many modern bathroom floor cabinets make use of either oak or maple components.
However, many manufacturers have expanded their lines to include the use of cherry, hickory as well as pine.
Elaborate bathroom designs might include more than one bathroom floor cabinets in varying finishes to add more effect.
Redoing your bathroom need not be an expensive undertaking.
The most basic and not to mention most economical way of sprucing up an old bathroom is through installing factory manufactured components, This include bathroom sinks as well as bathroom floor cabinets.
Installing a bathroom floor is a fairly easy thing to do.
Any homeowner can do it themselves as a DIY(Do-It-Yourself) project by following some very easy steps.
First thing you must do is to shut off the water service to the sink fixture and disconnect plumbing as well.
If it doesn't have shut-off valves, the main supply to the entire house should be shut off.
If the installation cannot be finished quickly, the bathroom supply lines might need to be capped so that the water service can be turned back on.
Many homeowners also use the time that the water supply is hut down to install new bathroom floor covering, besides the bathroom floor cabinet.
Installation can be done very quickly and is usually done within several hours.
Accurate measurements of the space for the new bathroom floor cabinet is a vital step in making sure that you are getting a cabinet that would properly fit the available space.
Take measurements of the location for both the hot and cold plumbing lines, and then create markings for each one, centered on the back area of the vanity sink cabinet.
After that cut openings for each one making sure that you leave some space to connect all the fittings later.
Set the bathroom floor cabinet in place, making use of the wall markings, be sure to check that they are solidly in place and are leveled.
If they are not leveled, you can make use of wood shims.
Secure it in place through the use of 3-inch screws through the nailer and going into the wall stud.
Then re-check its level again.
If doing it yourself seems more work than you would want to do yourself, you can always hire someone to install the bathroom floor cabinet for you.
There are many skilled people who can do it.
But still, it would not hurt to try it yourself as many of the factory manufactured bathroom floor cabinets actually come with a step by step process that you can follow while you install it.
You can also research about which ways are the easiest as there are, of course, various ways of installing it and each one differs in difficulty.
You can also ask help from someone who knows a little bit about carpentry although these skills are not required to be able to do it yourself.